series mlw snap-in miniature rockers b106 indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable b rockers touch tilt toggles www.nkkswitches.com general specifcations electrical capacity power level: 5a @ 125v ac, 3a @ 250v ac, & 3a @ 30v dc other ratings contact resistance: 10 milliohms maximum insulation resistance: 200 megohms minimum @ 500v dc dielectric strength: 1,000v ac minimum between contacts for 1 minute minimum; 1,500v ac minimum between contacts & case for 1 minute minimum mechanical life: 30,000 operations minimum electrical life: 10,000 operations minimum nominal operating force: 9.94n for rockers & 4.41n for paddles angle of throw: 24 for on-none-(on); 28 for all other circuits materials & finishes housing: stainless steel movable contacts: silver alloy stationary contacts: silver base: phenolic resin common terminal: copper with silver plating end terminals: copper with silver plating lamp terminals: phosphor bronze with nickel plating environmental data operating temperature range: C10c through +50c (+14f through +122f) humidity: 90 ~ 95% humidity for 96 hours @ 40c (104f) vibration: 10 ~ 55hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours shock: 50g (490m/s 2 ) acceleration (tested in 3 right angled directions, with 3 shocks in each direction) installation cap installation force: 9.80n (2.2 lbf) for rockers; 19.61n (4.4 lbf) for paddle soldering time & temperature: manual soldering: see profle a in supplement section. standards & certifications ul: file no. e44145 - recognized only when ordered with marking on switch. add /u or /cul before frst dash in part number to order ul recognized switch. all models recognized at 5a @ 125v ac & 3a @ 250v ac.
series mlw snap-in miniature rockers b107 indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable toggles b rockers touch tilt www.nkkswitches.com distinctive characteristics actual size industrys frst miniature snap-in, lighted rocker switch. actuators in various styles operate with frm, well-defned movements. interlocking actuator prevents switch failure due to jamming or window locking. two bezel sizes adapt to varied panel cutouts. unique stainless steel retaining clips securely hold switches over a range of panel thicknesses, even when exposed to vibration. space conserving front panel mounting with minimum behind panel dimension of .902 (22.9mm). durable stainless steel housing prevents corrosion. isolated lamp circuit for incandescent, led, and neon lamps. front panel relamping. built-in protective cover shields contacts from dust. epoxy sealed solder lug terminals lock out fux, dust, and other contaminants. extended lamp terminal for ease of wiring. matching indicators available.
b108 poles 1 spdt 2 sp3t dpdt typical switch ordering example 2 12 mlw30 1a standard 1a black 1b white 1c red 1d orange 1e yellow 1f green 1g blue 1h gray large 2a black 2b white 2c red 2d orange 2e yellow 2f green 2g blue 2h gray description for typical ordering example mlw3025-12-dc-1a 5 dc circuits 2 on none on 3 on off on 5 on none (on) 8 (on) off (on) 9 on off (on) 0 on on on ( ) = momentary cap types & colors incandescent & neon lamps 00 no lamp 06 6-volt 12 12-volt 18 18-volt 24 24-volt 28 28-volt n 110-volt (not suitable with green & blue) rocker ra black rb white rc red rd orange re yellow rf green rg blue paddle pa black pb white pc red pd orange pe yellow pf green pg blue design rocker db white dc red dd orange df green dg blue led rocker lb white lc red le yellow lf green sculptured rocker sb white sc red se yellow sf green lamps single element led colors c red e yellow f green bezels/colors 12-volt incandescent lamp design cap (black rocker base with red filter) dpdt on-none-(on) circuit black .787 (20.0mm) wide bezel important: switches are supplied without ul & culus markings unless specifed. ul & culus recognized only when ordered with marking on the switch. specifc models and ratings noted on the general specifcations page. series mlw snap-in miniature rockers indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable b rockers touch tilt toggles www.nkkswitches.com
b109 terminals switch terminals lamp terminals center terminal is .020 (0.5mm) longer thk = (0.8) .031 (5.9) .232 (1.2) dia .047 (3.0) .118 thk = (0.8) .031 (1.1) .043 (2.0) .079 (2.0) .079 (4.0) .157 lamp codes & specifications electrical specifcations are determined at a basic temperature of 25c. lamp circuit is independent of switch operation. for dimension drawings of lamps see accessories & hardware section. for neon, if the source voltage is greater than rated voltage, a ballast resistor is required. the ballast resistor calculation and more lamp detail are shown in the supplement. incandescent & neon lamps for solid & design caps voltage v 6v ac 12v ac 18v ac 24v ac 28v ac 110v ac current i 80ma 50ma 35ma 25ma 22ma 1.5ma mscp .159 .215 .398 .215 .247 na endurance hours 2,000 average 15,000 average ambient temperature range C10c ~ +50c C10c ~ +50c recommended resistor for neon: 33k ohms for 110v ac; 100k ohms for 220v ac no lamp code 00 indicates that no lamp is used. 00 at602n neon t-1 1 ? 2 pilot slide base 12 18 06 n 24 at602 incandescent 28 l(+) l(-) poles & circuits rocker position ( ) = momentary connected terminals throw & power/lamp schematics pole model down center up down center up notes: terminal numbers are not actually on switch. lamp circuit is isolated and requires an external power source. sp mlw3012 mlw3013 mlw3015 mlw3018 mlw3019 on on on (on) on none off none off off on on (on) (on) (on) 2-3 open 2-1 spdt dp mlw3022 mlw3023 mlw3025 mlw3028 mlw3029 on on on (on) on none off none off off on on (on) (on) (on) 2-3 5-6 open 2-1 5-4 dpdt l (+) (-) l l (+) (-) l 2 (com) 1 3 4 6 1 3 25 (com) for 3 throw (3-on) pole model down center up connected terminals & schematics external connection sp mlw3020 on on on the sp3t model utilizes a double pole base. external connection must be made during feld installation. with external connection without external connection 2-6 2-3 5-6 2-4 2-3 5-4 2-1 2-1 5-4 (out) 63 2 1 4 5 (out) (out) external conn common (in) 1 (out) 4 (out) 6 (out) 2 (in) 3 5 external connection 1 (out) 4 (out) 6 (out) 2 (in) 3 5 external connection 1 (out) 4 (out) 6 (out) 2 (in) 3 5 external connection series mlw snap-in miniature rockers indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable toggles b rockers touch tilt www.nkkswitches.com
b110 led color codes & specifications optional bezels cap types & colors single element led resistor value calculation is shown in the supplement. color red yellow green maximum forward current i fm 30ma 30ma 30ma typical forward current i f 20ma 20ma 20ma forward voltage v f 1.85v 2.0v 2.1v maximum reverse voltage v rm 5v 5v 5v current reduction rate above 25c ?i f 0.40ma/c 0.40ma/c 0.40ma/c ambient temperature range C10c ~ +50c e at622 led c f ra at405 rocke r at438 design rocker t-1 3 ? 4 pilot slide base for incandescent or neon lamps rb rc rd re rf rg pa pb pc pd pe pf pg db dc dd df material: translucent polycarbonate standard finish: glossy translucent colored filter black rocker/paddle not for use with lamp opaque black rocker base lb lc le lf at4125 led rocker sb sc se sf at4127 sculptured rocker material: translucent polycarbonate standard finish: glossy color codes: black white red orange yellow green a b c d e f blue g 1a at204 standard bezel .787 (20.0mm) wide 1b 1c 1d 1f 1g 1h 1e 2a at9201 large bezel .937 (23.8mm) wide 2b 2c 2d 2f 2g 2h 2e material: polycarbonate standard finish: glossy material: polycarbonate standard finish: glossy dg (10.5) .413 (16.0) .630 (12.6) .496 (13.5) .531 (10.5) .413 (16.0) .630 (12.6) .496 (13.5) .531 translucent colored diffuser and opaque black rocker base (25.0) .984 (15.6) .614 (15.6) .614 (4.0) .157 (16.0) .630 (12.6) .496 (10.5) .413 (13.5) .531 (16.0) .630 (15.5) .610 (11.5) .453 for led (20.0) .787 (2.2) .087 (16.4) .646 (16.0) .630 (25.5) 1.004 (16.4) .646 (16.0) .630 (26.3) 1.035 (23.8) .937 (2.5) .098 at426 paddle (+) (-) series mlw snap-in miniature rockers indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable b rockers touch tilt toggles www.nkkswitches.com
b111 typical switch dimensions without bezel single & double pole actuator in up position terminals 4, 5, & 6 are not on single pole models mlw3022-12-pc standard bezel single & double pole actuator in up position terminals 4, 5, & 6 are not on single pole models mlw3022-12-rc-1a large bezel single & double pole actuator in up position terminals 4, 5, & 6 are not on single pole models mlw3022-12-pc-2a sculptured cap single & double pole actuator in up position terminals 4, 5, & 6 are not on single pole models mlw3022-c-sc-1a (15.6) .614 (0.5) .020 (0.5) .020 (5.9) .232 (1.2) dia ty p .047 (4.5) .177 (22.9) .902 (17.0) .669 (0.4) ty p .016 (0.8) ty p .031 (4.7) ty p .185 (4.0) .157 (4.5) .177 (1.1) x (2.0) ty p .043 x .079 (1.5) .059 nkk part no. this side (16.0) .630 (15.6) .614 (2.2) .087 (0.5) .020 (5.9) .232 (1.2) dia ty p .047 (5.4) .213 (22.0) .866 (17.0) .669 (0.4) ty p .016 (0.8) ty p .031 (4.7) ty p .185 (4.0) .157 (4.5) .177 (1.1) x (2.0) ty p .043 x .079 nkk part no. this side (22.0) .866 (15.6) .614 (2.5) .098 (0.5) .020 (5.9) .232 (1.2) dia ty p .047 (5.4) .213 (17.0) .669 (0.4) ty p .016 (0.8) ty p .031 (4.7) ty p .185 (4.0) .157 (4.5) .177 (1.1) x (2.0) ty p .043 x .079 nkk part no. this side (4.0) .157 (2.2) .087 (15.5) .611 (4.0) .157 (2.5) .098 (15.5) .611 (22.0) .866 (2.2) .087 (0.5) .020 (5.9) .232 (1.2) dia ty p .047 (6.1) .240 (17.0) .669 (0.4) ty p .016 (0.8) ty p .031 (4.7) ty p .185 (4.0) .157 (4.5) .177 (1.1) x (2.0) ty p .043 x .079 nkk part no. this side (16.0) .630 (4.0) .157 (14.5) .571 (21.0) .827 l (+) l (-) 6 5 4 3 2 1 (3.0) ty p .118 (2.0) ty p .079 (10.2) .402 (16.6) .654 (25.5) 1.004 l (+) l (-) 6 5 4 3 2 1 (3.0) t yp .118 (2.0) t yp .079 (10.2) .402 (16.6) .654 (20.0) .787 (26.3) 1.035 l (+) l (-) 6 5 4 3 2 1 (3.0) ty p .118 (2.0) ty p .079 (10.2) .402 (16.6) .654 (23.8) .937 (25.5) 1.004 l (+) l (-) 6 5 4 3 2 1 (3.0) ty p .118 (2.0) ty p .079 (10.2) .402 (16.6) .654 (20.0) .787 series mlw snap-in miniature rockers indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable toggles b rockers touch tilt www.nkkswitches.com
b112 panel cutouts & thicknesses without bezel .039 ~ .157 (1.0mm ~ 4.0mm) installation & maintenance (16.7) .657 (18.7) .736 (19.2) sq .755 with standard bezel at204 .039 ~ .118 (1.0mm ~ 3.0mm) with large bezel at9201 .039 ~ .118 (1.0mm ~ 3.0mm) (16.7) .657 (18.7) .736 led (+) marking this side actuator (+) marking note: when changing leds, match the positive polarity markings on both lamp base and actuator block. legends nkk switches can provide custom legends for caps. contact factory for more information. (20.0) .787 (4.67) ty p .184 (18.48) ty p .728 (3.15) ty p .124 (0.76) ty p .030 (0.76) ty p .030 (0.76) ty p .030 st op st ar t recommended print method: pad print epoxy based ink is recommended (3.8) dia .150 (20.0) .787 (5.0) dia .197 lamps and leds can be changed without removing the switch from the panel. the lamp extractor at107 assists in removing lamps and leds. at107 lamp extractor (16.0) .630 (14.48) .570 (12.6) .496 (9.56) .376 (1.52) ty p .060 (0.76) ty p .030 (8.16) .321 (14.6) .575 (13.08) .515 (11.2) .441 (1.52) ty p .060 (0.76) ty p .030 rocker design rocker & led rocker bezel shaded areas are printable areas. series mlw snap-in miniature rockers indicators accessories supplement tactiles keylocks rotaries pushbuttons illuminated pb slides programmable b rockers touch tilt toggles www.nkkswitches.com
|
